Home systems

Boiler Replacement Cost: Gas and Oil Systems (2026)

Boiler replacement cost by fuel and type, gas versus oil, standard versus condensing, plus the radiators, zoning, and labor that set your actual price.

Short answer: Boiler replacement cost commonly runs an illustrative $3,500 to $6,500 installed for an electric boiler, $4,000 to $7,500 for a standard efficiency gas boiler, $5,500 to $9,500 for an oil boiler, and $6,000 to $10,500 for a high-efficiency condensing gas or combi boiler. Whether your existing venting and radiators can be reused as-is, or need modification for the new unit, is the factor most likely to move your real number.

Two thick, dusty insulated pipes running along a dark basement ceiling above cinder block walls, with a small window letting in daylight on the right
What's on this page
  1. What a boiler replacement actually costs
  2. Boiler versus furnace: a genuinely different system
  3. Standard efficiency gas boiler
  4. High-efficiency condensing gas boiler
  5. Oil boiler replacement
  6. Electric boiler
  7. Combi boilers
  8. Venting: the hidden line item
  9. Zoning and distribution system compatibility
  10. Where the money goes on a condensing gas boiler replacement
  11. A worked example: replacing a failing atmospheric boiler
  12. Signs it is time to replace rather than repair
  13. Sizing a replacement correctly
  14. Permits, inspections, and who approves the work
  15. How to compare boiler replacement quotes
  16. Maintaining a new boiler to get its full working life
  17. Boiler replacement cost in a home sale or purchase
  18. The DIY boundary
  19. Radiant floor heat and boiler compatibility
  20. Steam boilers: an older system with its own rules
  21. Common mistakes
  22. The bottom line

Short answer: Boiler replacement cost commonly runs an illustrative $3,500 to $6,500 installed for an electric boiler, $4,000 to $7,500 for a standard efficiency gas boiler, $5,500 to $9,500 for an oil boiler, and $6,000 to $10,500 for a high-efficiency condensing gas or combi boiler. Whether your existing venting and radiators can be reused as-is, or need modification for the new unit, is the factor most likely to move your real number.

A boiler heats water or steam and distributes that heat through radiators, baseboard units or radiant floor tubing, a hydronic system that is genuinely different equipment from the forced-air furnace and ductwork most other heating cost guides assume. ProsNook prices boiler replacement the way a hydronic heating contractor actually scopes the job: by fuel and efficiency tier, by what the existing distribution system and venting can or cannot carry forward, and by the labor and controls work that sits around the unit itself. Price your own boiler type and venting situation in the job cost estimator as you read, and treat every figure below as a planning range to check against an actual in-person assessment rather than a quote.

Key takeaways

  • Illustratively, an electric boiler commonly runs $3,500 to $6,500 installed, a standard gas boiler $4,000 to $7,500, an oil boiler $5,500 to $9,500, and a condensing gas or combi boiler $6,000 to $10,500.
  • A boiler and a furnace are different equipment entirely: hydronic (water or steam through radiators or baseboard) versus forced-air (heated air through ductwork). They are priced and replaced separately.
  • Most replacements reuse the existing radiators or baseboard distribution system as-is; new venting is the more common hidden cost, especially converting from a masonry chimney to PVC for a condensing unit.
  • A combi boiler replaces both space heating and a separate hot water tank with one unit, but its hot water output is capacity-limited, so sizing it means sizing for simultaneous demand, not just heating load.
  • Boilers commonly outlast furnaces, with a 15 to 25 year or longer working life achievable with good maintenance, which is worth weighing against the upfront cost difference between efficiency tiers.

What a boiler replacement actually costs

The honest starting point, before comparing a single quote, is that boiler replacement cost depends on fuel and efficiency tier before anything else, because these are genuinely different pieces of equipment with different component costs and different installation requirements. As an illustrative framework for this cost file, an electric boiler, suited to smaller homes or where no gas or oil service exists, commonly runs $3,500 to $6,500 installed. A standard efficiency gas boiler commonly runs $4,000 to $7,500. An oil boiler commonly runs $5,500 to $9,500. A high-efficiency condensing gas boiler or a combi boiler commonly runs $6,000 to $10,500.

None of those figures is a quote. They exist so that when a heating contractor names a number, you can place it within the right category and ask informed questions about why your specific job lands where it does inside that band rather than simply accepting or rejecting the total on its own.

Boiler versus furnace: a genuinely different system

It is worth being precise about this distinction before pricing anything, because the two are easy to confuse in casual conversation but are entirely different equipment. A boiler heats water or produces steam and sends it through radiators, baseboard heating units, or radiant tubing embedded in a floor, a system called hydronic heating. A furnace heats air directly and pushes it through ductwork to vents throughout the house, called forced-air heating. A home has one primary system or the other, not both, though a boiler-heated home sometimes has separate ductwork installed just for central air conditioning.

If your home actually has a furnace and ducted air, our furnace replacement cost file and our new HVAC system cost file price that equipment specifically, including the heat pump option within forced-air systems. This file prices the boiler and hydronic side of the comparison, which is common in older homes, particularly in colder regions and in homes with radiators as original equipment.

Standard efficiency gas boiler

A standard, or atmospheric, efficiency gas boiler is the traditional, non-condensing design that has heated homes for generations, venting its exhaust at a higher temperature through a conventional metal vent or masonry chimney. It remains a reliable, less expensive option, particularly in a home whose existing chimney venting is in good condition and sized correctly for the new unit.

Illustratively, a standard efficiency gas boiler commonly runs $4,000 to $7,500 installed, with the lower end reflecting a straightforward swap reusing existing venting and distribution, and the higher end reflecting a larger unit, a more complex installation, or venting work the existing chimney needs regardless of boiler choice, work that an older chimney liner sometimes requires even when the boiler itself is a direct like-for-like replacement.

High-efficiency condensing gas boiler

A condensing boiler captures additional heat from the combustion exhaust by cooling it enough that water vapor condenses out, extracting energy a standard efficiency unit simply vents to the outdoors. This pushes efficiency ratings meaningfully higher, which translates to lower fuel bills over the unit’s life, but the cooler, acidic condensate is corrosive to a conventional metal vent or masonry chimney, so condensing boilers typically vent through PVC pipe instead.

Illustratively, a condensing gas boiler commonly runs $6,000 to $10,500 installed, with the premium reflecting both the more sophisticated unit itself and, very commonly, the cost of converting venting from an existing masonry chimney to new PVC. Whether the higher upfront cost and venting change pay for themselves depends on your fuel costs, your climate, how long you plan to stay in the home, and the actual efficiency gap between the specific units you are comparing, a calculation worth running with real numbers from your contractor rather than assuming efficiency alone justifies the premium in every case.

Oil boiler replacement

In homes without access to natural gas service, oil remains a common boiler fuel, particularly in older housing stock in parts of the country, often rural or coastal, where gas infrastructure never reached. Oil boilers require their own burner equipment and typically an on-site storage tank, which is a separate piece of infrastructure from the boiler itself and ages on its own schedule.

Illustratively, an oil boiler replacement commonly runs $5,500 to $9,500 installed, generally running a bit higher than a comparable gas unit given the oil-specific burner componentry and the equipment required to handle the fuel delivery. If the existing oil tank is older or shows signs of corrosion, tank replacement is a separate line, illustratively $1,500 to $3,500, worth having inspected at the same time as the boiler rather than discovering as a second unplanned project shortly after the first one wraps up. Some homeowners replacing an aging oil system explore converting to gas where a line is accessible nearby; that conversion is a substantially larger project involving a new gas line, different venting, and typically oil tank decommissioning, and is worth pricing and deciding as its own separate question rather than assumed into a straightforward boiler swap.

Electric boiler

An electric boiler heats water using electric resistance elements rather than burning a fuel, which eliminates the need for venting, a gas line, or fuel storage entirely. This makes it a practical option for smaller homes, apartments, homes without gas service and no desire to install oil infrastructure, or situations where the simplicity of no combustion and no venting outweighs electricity’s generally higher cost per unit of heat compared with gas in most markets.

Illustratively, an electric boiler commonly runs $3,500 to $6,500 installed, often landing at the lower end of the overall category since it skips venting work entirely, though ongoing operating cost should be weighed against that lower installation figure using your local electricity and gas rates rather than installation price alone, since the lower upfront number does not automatically translate into the lower total cost over the unit’s working life.

Combi boilers

A combination, or combi, boiler provides both space heating and domestic hot water from a single unit, heating water on demand for taps and showers rather than relying on a separate storage tank. This appeals to homes with limited mechanical space, since it eliminates a separate water heater entirely.

Illustratively, a combi boiler commonly runs $5,500 to $9,000 installed, comparable to a standard condensing boiler given that most combi units are condensing by design and share much of the same core technology. The genuine sizing consideration is that a combi boiler’s hot water output is limited to its instantaneous heating capacity, so a unit undersized for a household’s simultaneous hot water demand, two showers running at once, for example, will show that limitation immediately. Our tankless water heater cost file covers the sizing logic for demand-based hot water in more depth, since a combi boiler’s hot water side works on the same underlying principle as a standalone tankless unit, just sharing the same combustion chamber as the heating side.

Two thick, dusty insulated pipes running along a dark basement ceiling above cinder block walls, with a small window letting in daylight on the right
The boiler itself is not pictured here, but insulated distribution pipes like these, running overhead through an older basement mechanical space, are a common sight in the same rooms a boiler replacement happens in.

Venting: the hidden line item

Venting is frequently the detail that separates a straightforward boiler swap from a more involved and more expensive project. A standard efficiency gas or oil boiler typically vents through a metal vent connector into a masonry chimney or a dedicated metal flue, and replacing like-for-like generally reuses that path if it is in sound condition and correctly sized.

A condensing boiler changes this because its cooler, acidic exhaust requires PVC venting rather than the materials used for a conventional unit’s hotter flue gas, which means converting from an existing masonry chimney to new PVC piping run to an exterior wall or roof penetration. Illustratively, this venting conversion commonly adds $500 to $1,800 to a condensing boiler installation, moving with how far the new vent pipe has to travel to reach a suitable exterior termination point. Ask directly whether a condensing boiler quote includes this conversion or assumes your existing venting is already compatible, since that assumption is frequently wrong on a home old enough to still have its original boiler.

Zoning and distribution system compatibility

Most boiler replacements reuse the home’s existing radiators, baseboard units or radiant tubing as-is, since the distribution system and the boiler that heats water for it are separate components with separate lifespans. A properly sized new boiler matched to an existing, sound distribution system typically needs no changes to the radiators or baseboard themselves.

Where changes are needed, zone valves, which allow different areas of the house to be heated independently, commonly run an illustrative $300 to $1,200 per zone to add or replace, and this is sometimes bundled into a replacement when the existing zoning is being reconfigured or expanded at the same time. New radiators or baseboard units, needed if the existing ones are failing, insufficient for the new boiler’s output characteristics, or part of an addition, commonly run $200 to $600 each, depending on style, material and output capacity. A heating contractor performing a proper heat loss calculation before sizing the new boiler is the step that confirms whether your existing distribution system genuinely matches the replacement, rather than assuming a same-output swap is automatically correct for a home whose insulation, windows or additions may have changed since the original boiler was sized decades earlier.

Illustrative installed cost by boiler type

Midpoint figures for a typical residential replacement. Bar widths are drawn from each value against the highest, $8,250 condensing gas or combi boiler.

Condensing gas or combi boiler$8,250
Oil boiler$7,500
Standard efficiency gas boiler$5,750
Electric boiler$5,000

Illustrative midpoints, not quotes. A condensing unit requiring new PVC venting lands toward the top of its band; a like-for-like swap on compatible existing venting lands near the bottom.

Where the money goes on a condensing gas boiler replacement

Breaking a typical condensing gas boiler replacement into its parts shows why the unit’s own price is only part of the total. Using an illustrative midpoint project, the boiler unit itself accounts for roughly 45 percent of the total, installation labor for about 30 percent, venting conversion for about 12 percent, and permit, controls and any zone valve work for the remaining 13 percent.

Where the money goes on a condensing gas boiler replacement

Shares of an illustrative midpoint project, summing to 100.

Unit cost 45% Installation labor 30% Permit and controls 13% Venting conversion 12%
Boiler unit, about 45% Installation labor, about 30% Permit, controls and zone valves, about 13% Venting conversion, about 12%

A swap reusing existing compatible venting shrinks that slice to near zero; a conversion from masonry chimney to PVC grows it meaningfully.

A worked example: replacing a failing atmospheric boiler

Numbers become useful stacked together. Take a fully illustrative example: a 25-year-old atmospheric gas boiler in an older home is showing its age, increasingly frequent repairs and visibly declining efficiency, and the homeowner decides to replace it with a mid-tier condensing unit while keeping the existing radiators, which are in sound condition.

The condensing gas boiler itself runs an illustrative $4,200. Installation labor, including removal of the old unit, hookup, and controls, runs $2,100. Because the old unit vented through a masonry chimney unsuitable for the new unit’s cooler exhaust, new PVC venting is required, adding $900. Permit and final inspection add $300. The total comes to roughly $7,500, inside the condensing boiler band.

Run your own boiler type, venting situation and any zoning changes through the estimator to see your version of this math.

Signs it is time to replace rather than repair

Deciding between another repair and a full replacement is a genuine financial judgment call, and a few factors tend to tip it one way or the other. Age is the starting point: a boiler approaching or past the upper end of its typical 15 to 25 year working life is a reasonable candidate for replacement at the next significant repair, since money spent on a major component failure for an aging unit is money that does not carry forward into a replacement that was likely coming within a few years anyway.

The nature of the failure matters as much as the age. A failure in the heat exchanger itself, the core component that transfers combustion heat into the water or steam, is frequently uneconomical to repair on an older unit, since the heat exchanger is often among the most expensive individual parts and a unit old enough to need one replaced is usually old enough to warrant replacing the whole boiler instead. A failure in a more peripheral component, a circulator pump, a specific control, or a sensor, is more often worth repairing regardless of the unit’s age, since these parts are both less expensive and more straightforward to replace without touching the boiler’s core.

A pattern of increasingly frequent service calls, even for different individual issues each time, is itself a signal worth weighing, since it suggests a unit generally wearing out across multiple systems rather than one isolated problem. Declining efficiency, visible as a rising fuel bill not explained by colder weather or any other obvious cause, suggests internal wear reducing how effectively the unit converts fuel into usable heat, and is a legitimate, if less dramatic, factor pointing toward replacement even on a boiler that has not yet had a dramatic failure.

Sizing a replacement correctly

A boiler sized incorrectly for a home, in either direction, causes real problems that are easy to misdiagnose as something else. An oversized boiler cycles on and off more frequently than it should, since it satisfies the home’s heat demand faster than the system’s thermostat and zoning were designed to work with, and that short cycling is harder on components and less efficient than a properly sized unit running longer, steadier cycles. An undersized boiler, by contrast, struggles to keep up during the coldest stretches of the year, running continuously without ever quite reaching the desired temperature, which reads to an occupant as “my boiler can’t keep the house warm enough,” a complaint sometimes misdiagnosed as a need for an even bigger replacement when the actual problem was a different sizing error entirely.

The correct sizing tool is a heat loss calculation, which accounts for your home’s square footage, insulation levels, window area and type, ceiling height and local climate design temperature to determine the actual heating load the boiler needs to meet. This is a meaningfully more precise method than simply matching the old boiler’s rated output, which may itself have been oversized or undersized from the original installation decades ago, carrying that original error forward into a brand new unit. Ask your contractor directly whether they performed a heat loss calculation or are sizing based on the existing unit’s rating, and treat a confident answer backed by an actual calculation as a sign of a contractor worth hiring.

Permits, inspections, and who approves the work

Boiler installation is permitted and inspected in virtually every jurisdiction, because a boiler is both a combustion appliance and a pressure vessel, and improperly installed venting, gas connections or pressure relief components are genuine safety hazards rather than cosmetic concerns. Permit requirements and fees are set locally and vary by municipality, so this cost file states no universal figure; confirm the requirement and cost with your local building department.

A licensed heating contractor who pulls the permit and arranges the required inspection as standard practice is doing the job correctly, not adding unnecessary cost, and skipping this step risks real problems later, at a home sale, with an insurance claim, or in the rare event something goes wrong with improperly inspected combustion equipment.

A man in a white hard hat and a high-visibility vest holding a clipboard while examining a blue electrical junction box mounted on exposed wood wall framing
A rough-in inspection on a different system, shown here, but a finished boiler installation goes through a comparable final inspection covering venting, gas connections and controls before the permit is closed.

How to compare boiler replacement quotes

Boiler quotes are difficult to compare because fuel type, efficiency tier and venting assumptions can all differ between bids addressing what looks like the same job. Build a single sheet and make each bidder state: the fuel and efficiency tier being quoted and why it fits your situation, whether a heat loss calculation was performed to size the unit, whether existing venting is being reused or converted and at what cost, whether existing radiators or baseboard are being reused as-is or need changes, the warranty on the unit and on labor separately, and whether the permit and inspection are included.

Be specifically cautious of a quote that proposes a condensing boiler without mentioning venting at all, since that is one of the most common places an otherwise competitive-looking bid turns out to be missing a real cost, and ask directly whether the contractor has priced your actual existing venting path or is assuming a standard scenario that may not match your home. Our quote comparison walkthrough covers the general discipline of reading bids by their assumptions, and our contractor vetting guide covers confirming licensing for this kind of combustion and pressure equipment work specifically.

Maintaining a new boiler to get its full working life

A new boiler installed correctly can still underperform its potential lifespan without reasonable ongoing maintenance, and a few habits make a genuine difference. Annual professional servicing, typically scheduled before the heating season starts, lets a technician check combustion efficiency, inspect for any developing leaks or corrosion, verify safety controls are functioning, and clean components that accumulate soot or scale over a season of operation. This is a modest recurring cost compared with the installation itself, and it is the single most effective thing an owner can do to protect that investment.

Water chemistry matters more for a boiler than most homeowners realize, since the same water circulates through the system repeatedly rather than being replaced the way domestic water is. Mineral buildup, corrosion, and sludge accumulation inside a hydronic system degrade heat transfer efficiency over time and can contribute to component wear, which is why some systems benefit from a water treatment additive or an inhibitor, a decision best made with your installer’s or service technician’s specific recommendation for your system and local water conditions rather than a generic assumption either way.

Keeping the area around the boiler clear of stored items, particularly anything flammable, is a basic safety habit worth maintaining consistently, since a boiler is combustion equipment regardless of how modern or well-maintained it is. And addressing any unusual sound, smell, or performance change promptly, rather than waiting for a scheduled service visit, catches a developing problem while it is still a minor repair rather than letting it progress into the kind of major failure that forces an unplanned, badly timed replacement decision.

Boiler replacement cost in a home sale or purchase

An aging or failing boiler is a common negotiating point in home sales, similar to an aging roof or an outdated electrical panel, and understanding how this typically plays out helps on either side of a transaction. A home inspection commonly notes the boiler’s apparent age, general condition, and any visible signs of trouble, though a general home inspector is not performing the detailed assessment a heating contractor would, so a flagged concern often prompts a follow-up quote from a specialist before the parties finalize how to handle it.

If you are selling a home with an aging boiler, having a recent service record and, ideally, a professional assessment of the unit’s remaining expected life ready to share with potential buyers puts you in a stronger negotiating position than an unknown history does, and it can be the difference between a buyer requesting a credit based on a worst-case assumption and one working from an actual professional opinion. If you are buying, treat an aging boiler flagged during inspection as worth a specific quote from a heating contractor before finalizing any requested credit or repair negotiation, since the actual replacement cost, informed by the specific fuel type, venting situation and distribution system covered throughout this cost file, is a far more useful number in a negotiation than a general inspector’s rough estimate.

The DIY boundary

Boiler installation sits firmly on the licensed-professional side of the line. It combines gas or oil fuel connections, venting that must be correctly sized and routed to safely remove combustion byproducts, electrical controls, and a pressure vessel operating at meaningful temperature and pressure, any one of which carries real consequences when done incorrectly, and licensing requirements in virtually every jurisdiction reflect that reality rather than existing as mere bureaucracy. This is not a DIY or handyman-scope project regardless of a homeowner’s general mechanical skill; our handyman cost file covers the general boundary between licensed trade work and work a handyman can legally perform, and boiler installation sits well inside the licensed side of that line.

Radiant floor heat and boiler compatibility

Radiant floor heating, tubing embedded in a floor slab or subfloor that circulates hot water to heat a space from the floor up rather than through radiators or baseboard, is a boiler-driven distribution system with its own specific considerations when the boiler feeding it is replaced. Radiant systems typically operate at lower water temperatures than radiators or baseboard units, and some newer high-efficiency condensing boilers are specifically well suited to this lower-temperature operation, actually running more efficiently at the temperatures radiant systems call for than they would feeding a higher-temperature radiator system.

A boiler replacement feeding an existing radiant system should be sized and configured with that system’s specific operating temperature and zoning in mind, and a contractor unfamiliar with radiant heating’s particular requirements can size or configure a replacement incorrectly in a way that either undersupplies the floors or runs the new boiler in a mode that gives up much of the efficiency advantage it was bought for. If your home has radiant floor heat, specifically ask any contractor quoting a replacement about their experience with radiant systems, since this is a meaningfully different skill set from a straightforward radiator or baseboard replacement.

Mixed systems, where part of a home uses radiant floor heat and another part uses radiators or baseboard fed from the same boiler, add a further layer of complexity to properly balancing output and temperature across both distribution types, and this is a legitimate reason to seek out a contractor with specific experience in multi-zone hydronic systems rather than a generalist.

Steam boilers: an older system with its own rules

Some older homes, particularly those built in the early to mid 20th century, use steam rather than hot water as the heating medium, a genuinely different hydronic approach where the boiler creates steam that rises through pipes to radiators, releases its heat as it condenses back into water, and that water returns to the boiler by gravity to be reheated. Steam systems have their own specific sizing, piping and control requirements that differ meaningfully from hot water systems, and replacing a steam boiler incorrectly, undersized, oversized, or paired with the wrong control strategy, produces characteristic problems: banging or hammering pipes, uneven heat between radiators, or a boiler that short cycles.

Illustratively, steam boiler replacement cost sits in a similar range to the standard and condensing gas figures covered earlier in this cost file, but the installation work itself often involves more piping adjustment than a hot water system replacement, since steam piping must be pitched correctly for condensate to return by gravity, and decades of settling or prior modifications can mean the existing piping needs real correction rather than a simple reconnection. If your home has a steam system, specifically seek a contractor with documented steam experience, since this is a specialized skill that has become less common as hot water systems have become the dominant choice in new construction, and a contractor who primarily installs hot water systems may not correctly diagnose or correct the piping issues a steam replacement often reveals.

Common mistakes

A handful of errors account for most of the frustration homeowners report with boiler replacement. Choosing a condensing unit for its efficiency rating without budgeting for the venting conversion it frequently requires is the most common, and it turns a seemingly attractive quote into a surprise mid-project. Skipping a proper heat loss calculation and simply matching the old boiler’s rated output is a close second, since an old boiler’s output may itself have been incorrectly sized decades ago, carrying that error forward into the replacement.

Not inspecting the oil tank alongside an oil boiler replacement, then facing a second unplanned project when the tank fails shortly after, is a third specific to oil systems. And confusing boiler replacement cost guidance with furnace replacement guidance, since the two terms get used loosely in casual conversation, leads some homeowners to price and budget the wrong equipment entirely.

A sixth mistake, specific to radiant floor and steam systems, is hiring a contractor without confirming their specific experience with that distribution type, since a generalist comfortable with standard radiator and baseboard replacements can genuinely mis-size or mis-configure a boiler feeding either of these less common systems, producing exactly the comfort and noise complaints covered earlier in this cost file.

The bottom line

Boiler replacement cost is set first by fuel type and efficiency tier, electric, standard gas, oil, or condensing gas and combi, and second by whether your existing venting and distribution system can be reused as-is or need modification for the new unit. Illustratively, an electric boiler commonly runs $3,500 to $6,500 installed, a standard gas boiler $4,000 to $7,500, an oil boiler $5,500 to $9,500, and a condensing gas or combi boiler $6,000 to $10,500.

Confirm whether your venting is compatible with the efficiency tier you are considering before comparing quotes, ask for a heat loss calculation rather than a same-output assumption, and inspect an aging oil tank alongside the boiler rather than after. Every figure here is illustration, and your real cost will move with your fuel type, your home’s existing venting and distribution system, local labor rates and the contractor you choose, so let a written quote built on an actual in-person assessment, including a heat loss calculation and, where relevant, specific experience with your distribution system, be the number you act on.


ProsNook publishes this cost file to explain how a residential boiler is selected, sized, priced and installed, and it is educational material rather than HVAC engineering, combustion safety or legal advice. No figure here is a quote: every dollar band, midpoint, share and worked total is illustration only, and your real cost will move with fuel type, efficiency tier, your home’s existing venting and distribution system, local labor and permit fees, and the sizing a proper heat loss calculation actually supports. Boiler installation involves combustion, venting, gas or oil fuel connections and pressure equipment, and is restricted by code and licensing requirements in virtually every jurisdiction; engage a licensed heating contractor and verify their license with the issuing authority. Permit requirements and fees are set locally and are described here in general terms only; confirm what applies at your address with your building department before work begins.

Frequently asked questions

How much does it cost to replace a boiler?

As an illustrative guide, replacing a boiler commonly runs about $3,500 to $6,500 installed for an electric boiler, $4,000 to $7,500 for a standard efficiency gas boiler, $5,500 to $9,500 for an oil boiler, and $6,000 to $10,500 for a high-efficiency condensing gas or combi boiler. The honest range depends on fuel type, efficiency tier, and whether your existing venting, radiators or baseboard distribution system can be reused as-is or need modification, which is a question only an in-person assessment of your specific heating system can answer.

What is the difference between a boiler and a furnace?

A boiler heats water or produces steam and distributes that heat through radiators, baseboard units, or in-floor radiant tubing, a system generally called hydronic heating, while a furnace heats air directly and distributes it through ductwork to vents throughout the house, a system called forced-air heating. The two approaches feel different to live with day to day, too, since hydronic heat tends to feel steadier and less drafty, while forced air responds faster and doubles as the delivery system for central air conditioning. These are genuinely different equipment categories with different distribution systems, and a home has one or the other, not both, for its primary heat source, though some homes pair a boiler with separate ductwork for central air conditioning. Our furnace replacement cost file and new HVAC system cost file price forced-air equipment specifically; this file prices the hydronic boiler side of home heating.

What is a condensing boiler and is it worth the extra cost?

A condensing boiler extracts additional heat from the combustion exhaust by cooling it enough that water vapor in the exhaust condenses, capturing energy a standard efficiency boiler simply vents outside into the atmosphere, which is why condensing units reach meaningfully higher efficiency ratings than their atmospheric counterparts. Illustratively, a condensing boiler commonly costs more upfront than a standard efficiency unit, but it also commonly requires different venting, PVC rather than a masonry chimney or metal vent, since the cooler exhaust is corrosive to materials designed for hotter flue gas. Whether the upfront premium and venting change pay off depends on your fuel cost, how much you heat, and how long you plan to stay in the home, which is a calculation worth running with your installer's efficiency numbers rather than assuming the answer.

What is a combi boiler?

A combi, or combination, boiler provides both space heating and domestic hot water on demand from a single unit, eliminating the need for a separate storage water heater tank. Illustratively, a combi boiler commonly runs $5,500 to $9,000 installed, a similar range to a standard condensing boiler, with the appeal being a smaller mechanical footprint and no separate tank to maintain or eventually replace. The tradeoff is that hot water output is limited to the unit's instantaneous capacity, so a combi boiler needs to be sized not just for heating load but for how much simultaneous hot water demand your household actually has, which our tankless water heater cost file covers in more depth for the domestic hot water side of that sizing question.

Can I keep my existing radiators when I replace a boiler?

In most straightforward replacements, yes. The radiators, baseboard units or in-floor radiant tubing are the distribution system, separate from the boiler that heats the water circulating through them, and a boiler replacement commonly reuses the existing distribution system as-is when it is in sound condition and properly sized for the new unit's output. The exceptions are a distribution system in poor repair, one that was never properly balanced across the house, or a significant change in the boiler's output relative to the old one, any of which may call for new or added radiators at an illustrative $200 to $600 each, a zoning change, or a professional heat loss calculation to confirm the match.

Do I need a permit to replace a boiler?

Yes, in virtually every jurisdiction, because a boiler is a combustion and pressure-vessel appliance and its installation, including venting and, for gas units, the gas line connection, is inspected accordingly. Permit requirements and fees are set locally and vary by municipality, so this cost file states no specific number as a universal figure; confirm the requirement and the fee with your local building department. A licensed heating contractor pulling the permit as standard practice is expected, not an unusual add, given the safety stakes of combustion equipment installed incorrectly.

How long does a boiler last, and how do I know mine needs replacing?

A well-maintained boiler commonly has a working life discussed in terms of 15 to 25 years or more, longer than a typical forced-air furnace, though real lifespan varies with water chemistry, maintenance history, installation quality and how hard the unit has worked over its life. Signs suggesting replacement rather than continued repair include age approaching or past that range, increasingly frequent repairs, visible rust or leaking at the boiler itself rather than just the distribution piping, declining efficiency or rising fuel bills unexplained by other causes, and a heating contractor's assessment that a major component failure is imminent on a unit old enough that repair no longer makes economic sense relative to replacement.

Is an oil boiler more expensive to replace than a gas boiler?

Illustratively, oil boiler replacement commonly runs somewhat higher than a comparable standard efficiency gas boiler, reflecting the oil-specific burner equipment and, where relevant, any work needed on the oil tank or supply line, with an oil boiler replacement commonly landing around $5,500 to $9,500 installed. Some homeowners replacing an oil system also consider converting to gas if a gas line is available nearby, which is a substantially larger project involving a new gas line and different venting, and is worth pricing as its own separate decision rather than assuming it is a simple swap at replacement time.

Editorial team · Home-services explainers

ProsNook guides are written by our editorial team, explaining how a contractor builds a bid and what makes one line item bigger than another, so a quote can be read line by line. Cost ranges are illustrative and labelled, not a quote for your job.

By email

Get a project cost breakdown by email

Tell us about your project and we'll email you a breakdown of what work like that typically costs and what a fair written quote should itemise. We are not a contractor or a matching service, we do not book jobs, and we will not pass your details to anyone.

We store your details to reply to you. See our privacy policy.